.\" Copyright (c) 2002 Hidetoshi Shimokawa .\" All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" .\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR .\" IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED .\" WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE .\" DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, .\" INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES .\" (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR .\" SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, .\" STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN .\" ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE .\" POSSIBILITY OF SUCH DAMAGE. .\" .\" $FreeBSD$ .\" .Dd October 24, 2006 .Dt FWCONTROL 8 .Os .Sh NAME .Nm fwcontrol .Nd FireWire control utility .Sh SYNOPSIS .Nm .Op Fl u Ar bus_num .Op Fl prt .Op Fl c Ar node .Op Fl d Ar node .Op Fl o Ar node .Op Fl s Ar node .Op Fl l Ar file .Op Fl g Ar gap_count .Op Fl b Ar pri_req .Op Fl M Ar mode .Op Fl R Ar filename .Op Fl S Ar filename .Op Fl m Ar EUI64 | hostname .Sh DESCRIPTION The .Nm utility is designed to provide a way for users to access and control the .Fx FireWire subsystem. Without options, .Nm will output a list of devices that are/were connected to the bus. .Pp The following options are available: .Bl -tag -width indent .It Fl u Ar bus_num Specify the FireWire bus number to be operated on. .It Fl r Initiate bus reset. .It Fl t Show the topology map. .It Fl p Dump PHY registers. .It Fl c Ar node Show the configuration ROM on the node. .It Fl d Ar node Hex dump of the configuration ROM. .It Fl o Ar node Send a link-on PHY packet to the node. .It Fl s Ar node Write to the .Dv RESET_START register on the node. .It Fl l Ar file Load hex dump file of the configuration ROM and parse it. .It Fl g Ar gap_count Broadcast .Ar gap_count by phy_config packet. .It Fl i Ar pri_req Set the .Dv PRIORITY_BUDGET register on all supported nodes. .It Fl M Ar mode Explicitly specify either .Ar dv or .Ar mpeg mode for the incoming stream. Only meaningful in case of and must precede the .Fl R option. If not specified, the program will try to guess. If you get an error complaining about "format 0x20", try to force the "mpeg" mode. .It Fl R Ar filename Receive DV or MPEG TS stream and dump it to a file. Use Ctrl-C to stop the receiving. Some DV cameras seem not to send the stream if a bus manager exits. If you cannot get the stream, try the following commands: .Bd -literal -offset indent sysctl hw.firewire.try_bmr=0 fwcontrol -r .Ed .Pp The resulting file contains raw DV data excluding isochronous header and CIP header. It can be handled by .Nm libdv in the .Fx Ports Collection. Resulting MPEG TS stream can be played and sent over a network using the VideoLAN .Nm vlc tool in the .Fx Ports Collection. The stream can be piped directly to .Nm vlc, see EXAMPLES. .It Fl S Ar filename Send a DV file as isochronous stream. .It Fl m Ar EUI64 | hostname Set default fwmem target. Hostname will be converted to EUI64 using .Xr eui64 5 . .El .Sh FILES .Bl -tag .It Pa /dev/fw0.0 .El .Sh EXAMPLES Each DV frame has a fixed size and it is easy to edit the frame order. .Pp .Dl "fwcontrol -R original.dv" .Pp Receive a DV stream with DV camera attached. .Pp .Dl "dd if=original.dv of=first.dv bs=120000 count=30" .Pp Get first 30 frames(NTSC). .Pp .Dl "dd if=original.dv of=second.dv bs=120000 skip=30 count=30" .Pp Get second 30 frames(NTSC). .Pp .Dl "cat second.dv first.dv | fwcontrol -S /dev/stdin" .Pp Swap first and second 30 frames and send them to DV recorder. .Pp For PAL, replace .Dq Li bs=120000 with .Dq Li bs=144000 . .Pp .Dl "fwcontrol -R file.m2t .Pp Receive an MPEG TS stream from a camera producing MPEG transport stream. This has been tested with SONY HDR-FX1E camera that produces HD MPEG-2 stream at 25 Mbps bandwidth. .Pp To send the stream from the camera over the network using TCP (which supprisingly works better with vlc), you can use .Dl "fwcontrol -R - | nc 192.168.10.11 9000 with .Nm netcat from ports and to receive the stream, use .Dl nc -l -p 9000 | vlc - .Pp To netcast via UDP, you need to use .Nm buffer program from ports, since vlc is not fast enough to read UDP packets from buffers and thus it experiences dropouts when run directly. The sending side can use .Dl "fwcontrol -R - | nc 192.168.10.11 9000 and to receive the stream, use .Dl nc -l -u -p 9000 | buffer -s 10k -b 1000 -m 20m -p 5 | vlc - .Pp .Pp For more information on how to work with .Nm vlc see its docs. .Sh SEE ALSO .Xr firewire 4 , .Xr fwe 4 , .Xr fwip 4 , .Xr fwohci 4 , .Xr sbp 4 , .Xr mplayer 1 , .Xr vlc 1 .Sh HISTORY The .Nm utility first appeared in .Fx 5.0 . .Sh AUTHORS .An Hidetoshi Shimokawa Aq simokawa@FreeBSD.org .An Petr Holub Aq hopet@ics.muni.cz - MPEG TS mode. .Sh BUGS This utility is still under development and provided for debugging purposes. Especially MPEG TS reception support is very rudimental and supports only high-bandwidth MPEG-2 streams (fn field in CIP header equals 3).