]> June 7, 2013 rndc 8 BIND9 rndc name server control utility 2004 2005 2007 2013 Internet Systems Consortium, Inc. ("ISC") 2000 2001 Internet Software Consortium. rndc -b source-address -c config-file -k key-file -s server -p port -V -y key_id command rndc controls the operation of a name server. It supersedes the ndc utility that was provided in old BIND releases. If rndc is invoked with no command line options or arguments, it prints a short summary of the supported commands and the available options and their arguments. rndc communicates with the name server over a TCP connection, sending commands authenticated with digital signatures. In the current versions of rndc and named, the only supported authentication algorithm is HMAC-MD5, which uses a shared secret on each end of the connection. This provides TSIG-style authentication for the command request and the name server's response. All commands sent over the channel must be signed by a key_id known to the server. rndc reads a configuration file to determine how to contact the name server and decide what algorithm and key it should use. -b source-address Use source-address as the source address for the connection to the server. Multiple instances are permitted to allow setting of both the IPv4 and IPv6 source addresses. -c config-file Use config-file as the configuration file instead of the default, /etc/rndc.conf. -k key-file Use key-file as the key file instead of the default, /etc/rndc.key. The key in /etc/rndc.key will be used to authenticate commands sent to the server if the config-file does not exist. -s server server is the name or address of the server which matches a server statement in the configuration file for rndc. If no server is supplied on the command line, the host named by the default-server clause in the options statement of the rndc configuration file will be used. -p port Send commands to TCP port port instead of BIND 9's default control channel port, 953. -V Enable verbose logging. -y key_id Use the key key_id from the configuration file. key_id must be known by named with the same algorithm and secret string in order for control message validation to succeed. If no key_id is specified, rndc will first look for a key clause in the server statement of the server being used, or if no server statement is present for that host, then the default-key clause of the options statement. Note that the configuration file contains shared secrets which are used to send authenticated control commands to name servers. It should therefore not have general read or write access. A list of commands supported by rndc can be seen by running rndc without arguments. Currently supported commands are: reload Reload configuration file and zones. reload zone class view Reload the given zone. refresh zone class view Schedule zone maintenance for the given zone. retransfer zone class view Retransfer the given zone from the master. sign zone class view Fetch all DNSSEC keys for the given zone from the key directory (see the key-directory option in the BIND 9 Administrator Reference Manual). If they are within their publication period, merge them into the zone's DNSKEY RRset. If the DNSKEY RRset is changed, then the zone is automatically re-signed with the new key set. This command requires that the auto-dnssec zone option be set to allow or maintain, and also requires the zone to be configured to allow dynamic DNS. (See "Dynamic Update Policies" in the Administrator Reference Manual for more details.) loadkeys zone class view Fetch all DNSSEC keys for the given zone from the key directory. If they are within their publication period, merge them into the zone's DNSKEY RRset. Unlike rndc sign, however, the zone is not immediately re-signed by the new keys, but is allowed to incrementally re-sign over time. This command requires that the auto-dnssec zone option be set to maintain, and also requires the zone to be configured to allow dynamic DNS. (See "Dynamic Update Policies" in the Administrator Reference Manual for more details.) freeze zone class view Suspend updates to a dynamic zone. If no zone is specified, then all zones are suspended. This allows manual edits to be made to a zone normally updated by dynamic update. It also causes changes in the journal file to be synced into the master file, and the journal file to be removed. All dynamic update attempts will be refused while the zone is frozen. thaw zone class view Enable updates to a frozen dynamic zone. If no zone is specified, then all frozen zones are enabled. This causes the server to reload the zone from disk, and re-enables dynamic updates after the load has completed. After a zone is thawed, dynamic updates will no longer be refused. notify zone class view Resend NOTIFY messages for the zone. reconfig Reload the configuration file and load new zones, but do not reload existing zone files even if they have changed. This is faster than a full reload when there is a large number of zones because it avoids the need to examine the modification times of the zones files. stats Write server statistics to the statistics file. querylog on|off Toggle query logging. Query logging can also be enabled by explicitly directing the queries category to a channel in the logging section of named.conf or by specifying querylog yes; in the options section of named.conf. dumpdb -all|-cache|-zone view ... Dump the server's caches (default) and/or zones to the dump file for the specified views. If no view is specified, all views are dumped. secroots view ... Dump the server's security roots to the secroots file for the specified views. If no view is specified, security roots for all views are dumped. stop -p Stop the server, making sure any recent changes made through dynamic update or IXFR are first saved to the master files of the updated zones. If -p is specified named's process id is returned. This allows an external process to determine when named had completed stopping. halt -p Stop the server immediately. Recent changes made through dynamic update or IXFR are not saved to the master files, but will be rolled forward from the journal files when the server is restarted. If -p is specified named's process id is returned. This allows an external process to determine when named had completed halting. trace Increment the servers debugging level by one. trace level Sets the server's debugging level to an explicit value. notrace Sets the server's debugging level to 0. flush Flushes the server's cache. flushname name view Flushes the given name from the server's cache. status Display status of the server. Note that the number of zones includes the internal bind/CH zone and the default ./IN hint zone if there is not an explicit root zone configured. recursing Dump the list of queries named is currently recursing on. validation ( on | off | check ) view ... Enable, disable, or check the current status of DNSSEC validation. Note dnssec-enable also needs to be set to yes or auto to be effective. It defaults to enabled. tsig-list List the names of all TSIG keys currently configured for use by named in each view. The list both statically configured keys and dynamic TKEY-negotiated keys. tsig-delete keyname view Delete a given TKEY-negotiated key from the server. (This does not apply to statically configured TSIG keys.) addzone zone class view configuration Add a zone while the server is running. This command requires the allow-new-zones option to be set to yes. The configuration string specified on the command line is the zone configuration text that would ordinarily be placed in named.conf. The configuration is saved in a file called hash.nzf, where hash is a cryptographic hash generated from the name of the view. When named is restarted, the file will be loaded into the view configuration, so that zones that were added can persist after a restart. This sample addzone command would add the zone example.com to the default view: $ rndc addzone example.com '{ type master; file "example.com.db"; };' (Note the brackets and semi-colon around the zone configuration text.) delzone zone class view Delete a zone while the server is running. Only zones that were originally added via rndc addzone can be deleted in this manner. There is currently no way to provide the shared secret for a key_id without using the configuration file. Several error messages could be clearer. rndc.conf5 , rndc-confgen8 , named8 , named.conf5 , ndc8 , BIND 9 Administrator Reference Manual. Internet Systems Consortium